| 1 | 1 | FOR : DINJAN | | | |
|---|
| 2 | 1.01 | Peg Table. Peg table of size 450mm x400 x 380mm as per drawing. Table top will be 18mm thick pre laminated PDF board of grade-1, exterior quality as per IS-14587 shall be provided. All the wood work and veneered surface shall be French polished. Ffirst grade seasoned teak wood as per IS free from knots and cracks shall be used. 6 mm thick teak woodn lipping shall be provided on all the exposed edges of MDF duly treated with french polish as specified. The legs will be fitted with PVC shoe hard. All as per Drg No FD/MAP/11 sheet 1/1 and technical specification at in Schedule-III(A). | PEG TABLE | 42 | NOS |
|---|
| 3 | 2 | FOR : LEIMAKHONG | | | |
|---|
| 4 | 2.01 | Bed Side Locker. Bed side locker of size 0.90M x 0.50M x 1.0M made out of 20 gauge CR steel sheet conforming to IS:513:1994 amdt.1&2. The locker will have 2 compartments with 2 separate doors on the front side and a partition on the inner side in the middle dividing the width of the locker into 2 equal parts. Lft compartment will have two shelves placed horizontally at equal distance and right compartment will have one 20mm dia steel rod 65mm below top level for hangar arragement. Vertical reinforcement of 800/400 mm to be fitted inside on both the doors as well as on right side of the locker (hanger side) all as per drg and as per specification in Schedule-III(A). The locker shall be painted dark OG colour/as indicated by consignee. | BSL | 128 | NOS |
|---|
| 5 | 2.02 | Bed Side Locker Large. Bed side locker of size 1.20M x 0.50M x 1.50M made out of 20 gauge CR steel sheet conforming to IS:513:1994 amdt.1&2. The locker will have 2 compartments with 2 separate doors on the front side and a partition on the inner side in the middle dividing the width of the locker into 2 equal parts. Each compartment will have a shelf placed horizontally at 60cm above cill level and one 20mm dia hanger steel rod 80mm below the top level all as per drg and as per specification in Schedule-III(A). The locker shall be painted dark OG colour/as indicated by consignee. | BSL (L) | 4 | NOS |
|---|
| 6 | 2.03 | Chair Writing Wooden. Chair writing of size 535 x 470 x 890 mm shall be provided. Chair shall be made our of well seasnoed 1st class teak wood free from knots. All wooden exposed surfaces shall be finished with two coats of French polish high gloss finish after preparation of wooden surface. Plastic cane seat of size 470 x 470 x 535 with arm rest of size 60 x 25 mm shall provided. The legs will be fitted with hard PVC shoe. All as per drg No FD 280 sheet 1/1 and and technical specification at in Schedule-III(A). | CHAIR WRITING WOODEN | 19 | NOS |
|---|
| 7 | 2.04 | Writing Table. Table of size 1145 x 610 x 760 mm shall be provided. Table top shall be 19 mm thick pre-laminated decorated particle board fixed with hollow section frame with screw @ 200 mm c/c. The frame work of table shall be of MS hollow section of size 25 x 25 mm all as per drg. End of legs will be sealed with MS sheet 1.6 mm thick with proper welding process to avoid the dust entry. 6 mm thick teak woodn lipping shall be provided on all the exposed edges of MDF duly treated with french polish as specified. All steel surface will have two coats of synthetic enamel paint over a coat of red oxide primer. The legs will be fitted with hard PVC shoe. Refer Drg No WT 1/1 and technical specification at in Schedule-III(A). | WRITING TABLE | 19 | NOS |
|---|
| 8 | 2.05 | Peg Table. Peg table of size 450mm x400 x 380mm as per drawing. Table top will be 18mm thick pre laminated PDF board of grade-1, exterior quality as per IS-14587 shall be provided. All the wood work and veneered surface shall be French polished. Ffirst grade seasoned teak wood as per IS free from knots and cracks shall be used. 6 mm thick teak woodn lipping shall be provided on all the exposed edges of MDF duly treated with french polish as specified. The legs will be fitted with PVC shoe hard. All as per Drg No FD/MAP/11 sheet 1/1 and technical specification at in Schedule-III(A). | PEG TABLE | 12 | NOS |
|---|
| 9 | 2.06 | Chair Dining. Chair dining of size 440 x 430 x 890 mm shall be provided. Chair shall be made out of well seasoned 1st class teak wood free from knots. All wooden exposed surfaces shall be finished with two coat of French polish high gloss finish after preparation of wooden surfaces. Single piece seat of size 440 x 430 x 405 mm with 4 x 10 mm thick ribbs moulded shall be provided. The legs will be fitted with hard rubber shoe. All as per Drg No FD/MAP/03 SH 1/1 and technical specification at in Schedule-III(A). | DINING CHAIR | 72 | NOS |
|---|
| 10 | 2.07 | Dining Table. Table dining of size 1800 x 900 x 750 mm shall be provided. Table top shall be 19 mm thick pre-laminated decorated particle board sheet fixed with hollow section frame with screw @ 200 mm c/c. The frame work of table shall be of MS hollow section of size 25 x 25 mm all as per drg. End of legs will be sealed with MS sheet 1.6 mm thick with proper welding process to avoid the dust entry. 6 mm thick teak woodn lipping shall be provided on all the exposed edges of MDF duly treated with french polish as specified. All steel surface will have two coats of synthetic enamel paint over a coat of red oxide primer. The legs will be fitted with PVC shoe hard. Refer Drg No DT 1/1 and as per specification in Schedule-III(A). | DINNING TABLE | 12 | NOS |
|---|
| 11 | 2.08 | Store Rack. Consists of four platforms, each made of rigid angle iron frame work to hold 4' x 2', 12 mm thick ply wood. All four rigid platforms to be supported at four corners with angle iron vertical columns as per spacing mentioned in drg No SR-1/1 with suitable nut & bolts. Angle iron of size 40mm x 40mm x 5mm to be used. Bracing with MS flat of size 40mm x 5mm to be provided at the rear. All as per drg No SR-1/1 and technical specification at in Schedule-III(A). | RACK | 28 | NOS |
|---|
| 12 | 2.09 | Table Stainless Steel. Stainless Steel Table of size 1800 x 750 x 760 mm shall be provided. Table top shall be 14 gauge stainless steel sheet on top fixed with 35mm stainless steel square pipe with screw. The frame work of table shall be made of stainless steel tube of size 35 x 35 x 1.25 mm thick all as per drg. Stainless steel wire mesh shall be fixed at the bottom of the table as per drg. The legs will be fitted with hard rubber shoe. All as per drg No SST 1/1 and technical specification at in Schedule-III(A). | STAINLESS STEEL TABLE | 4 | NOS |
|---|
| 13 | 2.1 | AlmirahSteel Large. Almirah steel large shall as per drawing of size 1300x485x1985mm made up of 20 mm thick MS sheet. Four number of shelves shall be provided equally spaced to make five compartments. One chromium plated handle 150 mm long with 3 way locking device shall be provided. In addition one hasp and staple of size 150 mm long shall be provided for alternative locking arrangements. All steel surfaces internally and externally to be painted with 2 coats of synthetic enamel paint over a coat of red oxide. all as per Drg No ASL 1/1 and technical specification at in Schedule-III(A). | ALMIRAH STEEL (L) | 7 | NOS |
|---|
| 14 | 3 | FOR : LIKABALI | | | |
|---|
| 15 | 3.01 | Chair Writing Wooden. Chair writing of size 535 x 470 x 890 mm shall be provided. Chair shall be made our of well seasnoed 1st class teak wood free from knots. All wooden exposed surfaces shall be finished with two coats of French polish high gloss finish after preparation of wooden surface. Plastic cane seat of size 470 x 470 x 535 with arm rest of size 60 x 25 mm shall provided. The legs will be fitted with hard PVC shoe. All as per drg No FD 280 sheet 1/1 and and technical specification at in Schedule-III(A). | CHAIR WRITING WOODEN | 7 | NOS |
|---|
| 16 | 4 | FOR : DIMAUR | | | |
|---|
| 17 | 4.01 | Chair Writing Wooden. Chair writing of size 535 x 470 x 890 mm shall be provided. Chair shall be made our of well seasnoed 1st class teak wood free from knots. All wooden exposed surfaces shall be finished with two coats of French polish high gloss finish after preparation of wooden surface. Plastic cane seat of size 470 x 470 x 535 with arm rest of size 60 x 25 mm shall provided. The legs will be fitted with hard PVC shoe. All as per drg No FD 280 sheet 1/1 and and technical specification at in Schedule-III(A). | CHAIR WRITING WOODEN | 6 | NOS |
|---|
| 18 | 4.02 | Writing Table. Writing Table. Table of size 1145 x 610 x 760 mm shall be provided. Table top shall be 19 mm thick pre-laminated decorated particle board fixed with hollow section frame with screw @ 200 mm c/c. The frame work of table shall be of MS hollow section of size 25 x 25 mm all as per drg. End of legs will be sealed with MS sheet 1.6 mm thick with proper welding process to avoid the dust entry. 6 mm thick teak woodn lipping shall be provided on all the exposed edges of MDF duly treated with french polish as specified. All steel surface will have two coats of synthetic enamel paint over a coat of red oxide primer. The legs will be fitted with hard PVC shoe. Refer Drg No WT 1/1 and technical specification at in Schedule-III(A). | WRITING TABLE | 6 | NOS |
|---|
