Supply Of Machinery And Equipments ( 1 Instrumentation & Control Engineering 1.01 Pc Based Data Acquisition System With Sensors:- • Temp Sensors ( Lm35, Pt100 ) , Proximity Switches• Ldr ( Lm 324 & Ldr ) & Ir Sensors ( With Transmitter & Receiver With Encoder / Decoder ) , Proximity Switches ( Inductive / Capacitive ) • Photo Electric Sensors With Signal Conditioning And Other Required Circuitry, With Pc Interface Thru Usb Bus With Data Acquisition System• Having 8 Channel 12-Bit Analog Inputs, 2 Analog Outputs • 20 Digital Input Output Lines With 2 No Of Relays.• Complete Software Control & It Supports Lab View Software• On Board: 8 Digital Output ( Led’S ) On Board 8 Digital Input Switch Buzzer For Indication Facility For External Signal Interface, • It Supports Software Or Hardware Timed Acquisition• 2 Analog Outputs, 20 Digital I / O ( Up To 50 Hz Per I / O ) • 32-Bit Counter, With Watchdog Timer Function Usb 2.0 / 1.1 Low Speed Interface , On Board Programming Facility 1.02 Universal Transducer Trainer ( Universal Sensor / Instrumentation Trainer ) :- • On Board : Lvdt , Microphone, Hall Sensor, Strain Gauge, Ultrasonic Trans Receiver, • Temp Sensor; Lm35, Thermistor, Thermocouple, Humidity Sensor Etc.• Light Sensor:- Photo Diode, Photo Tx., Photo Voltaic Cell, Photo Conductive Cell, Ldr • Signal Conditioning: Instrumentation Amplifier, Class Amplifier, Differential Amplifier. • Square Wave Generator, Band Pass Filter, Variable Resistor: Servo Potentiometer, Slide Resister, Rotatry Resister, Wire Wound, Carbon Track• Buzzer, Voltmeter ( 0-15V ) , Test Point On Each Sections 1.03 Lvdt Trainer-20Mm :- Ac-Ac Spring Loaded 20Mm LvdtPic Microcontroller Based SystemLcd 16*2 Display Unit To Show Lvdt Output Results5Khz Frequency Generator With Test Points To Adjust FrequencyTest Points For Test Lvdt Calibration Using MultimeterOn Board Power Reset Switch With Led IndicatorBuzzer Indicator For Finding Lvdt Null PointOperational Amplifier And Signal Conditioning Circuit With Test PointsOptional: Programming Cable To Program And Develop Customized SolutionSystem Come With Operating User Manual, Connecting Cables & Power Supply 1.04 Piezo Electric Trainer:- Piezo Electric Transducer:1000 Pf Piezo-CrystalIndicator:31 / 2 Digit Display To Read Impact Force.Power Supply: 230V + / -10% @ 50 Hz 1.05 Load Cell Trainer:- Capacity Of 10Kg, Easy To Plug And Play UnitPower On / Off Switch With Led IndicationOperational Amplifier And Signal Conditioning CircuitLcd 16*2 Based Unit To Display Load StatusTest Points To Measure Different Signals And VoltageSystem Come With Operating User Manual, Connecting Cables & Power Supply 1.06 Proximity Sensor Trainer:- Platform To Learn Metal Detecting Facility Using Proximity Metal DetectorDc Motor Mechanism To Produce RpmRpm Count Display Facility To Observe Count ResultsSwitches Control To Control Direction And Motor SpeedVoltage Control Variac To Speedup, Speed Down The Counts, SpeedOptional: Usb Support To Program The Hardware And For Software ChangesTest Point For Conceptual Study During Different Hardware Operation 1.07 Ultrasonic Distance Sensor Trainer:- Range: 6 Inches To 15 InchesAccuracy: 1 InchIn Built Power Supply: 5 Volts DcOnboard Controlled Lcd DisplayOn Board Test Points To Study The Signals During Operation Of SensorFaults Study Using Hardware Switches, During Operation15 Inches Scale For Distance Measurement Concept Study 1.08 Accelerometer Sensor Trainer:- Onboard 3.3 V Low Drop Voltage Regulator With Input Range Of 3.6V To 6V.Supply Voltage ( Vdd ) : 2.2 V To 3.6V@400Μa ( Accelerometer Supply Range ) Senstivity: 1.5G: 800 Mv / G6G: 206 Mv / GStatic Acceleration : Xout, Yout @-1G: 0.85VBandwidth: X, Y Axis: 400HzOutput Impedance: 32Kω.Lcd Display To See Coordinates Values, Test Points To Measure Signals 1.09 Temperature Trainer Combo Lm35, Thermistor, Thermocouple, Rtd:- On Board Power Jack, Lcd 16*2 Display To Observe Temperature Of Different Temperature SensorsInput Banana Sockets To Test Lm35, Rtd, Thermistor, And J Type Thermocouple SensorSwitches Facility To Switch From One Sensor To Other, Operational Amplifier And Signal Conditioning Circuit To Compulsive OutputInbuilt Adc ConversionPic16f / 18F Compatible HardwareOver / Under Temperature Alert IndicatorPlastic Light Weight BaseEasy To Operate Trainer With Help Of User Manual And Video Tutorial.Square Wave Is Either Without Or With InterruptTemperature Source Electric Kettle 1.1 Speed Measurement Trainer:- Motor Capacity: 12V Dc Motor.• Max. Motor Speed: 1500 Rpm ( Approx. ) • Motor Input Supply: 12V Dc.• Motor Speed Control: Using Pot.• Tone Wheel: Ms Gear Wheel Of 60Teeth, Copper Wheel With 60 Slots• Sensor: Non- Contact Magnetic Pickup & Opto-Coupler Ic• Display: Digital Seven Segment Red Led Display To Read Upto 9999 Counts• Power Supply: 230V 50Hz. 1.11 Water Flow Measurement Trainer:- • 1~12 L / Min Flow Rate Range Measurement• Flow Control Provision• Flow Rate Display Unit• On Board Bnc Socket For Cro Connectivity• Provision For Measurement Of Frequency And Test Points To Measure Voltage Using Multimeter• Inbuilt Power Supply• Durable Water Container And Water Pump• Optional: 1 ) On Board Programming Facility2 ) Ultrasonic Measurement 1.12 Humidity Sensor Trainer:- Microcontroller Based Humidity Control SystemHumidity Sensor Module With Resistance TypeLinear Dc Output Voltage For 0-100% RhOn Board Syh-2 / Syhw-2 SensorsWide Temp. Compensation Range, Lcd DisplayOptional: On Board Programming Facility 1.13 Stepper Motor Trainer Kit:- Inbuilt Power Supply Of 24V Dc / 2.5ADual Channel 24V Dc Stepper Motor Driver And MotorSwitches For Controlling The Step AngleSwitch To Control Speed And DirectionBig ( Torque=3Nm ) And Small ( Torque=0.5Nm ) Stepper Motor With DriverTest Points To Measure Signals Lcd Display To Show Rpm AndDirection Control, In System Microcontroller Programming Facility, Powder Coated Metal Frame With Easy Assembles Facility. 1.14 Photo Transducer Kit Photo Cell, Photo Transistor, Photo Diode, Pin Photo Diode:- The Concept Circuit Of Optical Trainer Printed On P.C.B. , Inbuilt Power Supply SourceTransducers Photoconductive Cell, Photovoltaic Cell, Photo Transistor, Led , Photo Diode, Pin Photodiode Light Source - Filament Lamp, Signal Conditioning Circuitry Potentiometers, Output Circuits, Interconnections - 4Mm Banana Sockets, Ac Mains Operated, Operating Manual Output Device-, Moving Coil Meters, Analog Voltmeter And Current Meter. 1.15 Experimental Panel For Analog And Digital Plc:- Sequential Motor Starter Interface , Star / Delta Starter InterfaceDol Starter Interface , Water Level Controller, Reaction Vessel InterfaceResistance Welding Interface, Traffic Light InterfaceCar Parking Interface, Piston Cylinder InterfaceLogic Control SystemBottle Filling SystemRack FeederCascaded Control 1.16 Process Control Station:- TanksReservoir Tank 54 Litres ApproximatelyProcess Tank 1 37 Litres ApproximatelyProcess Tank 2 21 Litres ApproximatelyPump: Three Phase, 0.37 Kw, Flow Rate Up To 40 Litres Per Minute, Head Up To 40 MetersFlow Transducer : Electromagnetic Flow MeterPressure Transducer Measuring Ranges Up To 400 BarOutput 4 To 20 MaUltrasonic TransducerTemperature Transducer Pt 100 Sensing Element Dp Cell Measuring Ranges From –10...+10 Mbar To –40...+40 BarControl Valve 2 / 2–Way Globe Control Valve With Electronic Control Of PositioningVenturi Provides Flow Measurement For The Pump Delivery.Ethernet Gateway Ethernet / Profibus Dp Gateway With Integrated Web Server. Physical: Max. 31 Profibus Dp Devices Per Channel, Max. 125 Profibus Dp Devices If Repeaters Are UsedLogical Max. 125 Profibus Dp DevicesMotor Control Inverter 250V Ac 1.1Kw Including Profibus-D 1.17 Industrial Process Control System:- • Control Cabinet With Window• Dp / Pa Coupler• Tank 3 Nos• Ultrasonic Level Transmitter Maximum Measuring Range: 5 M In Fluids / 2 M In Bulk Materials• Three Phase Inverter With Profibus Dp Interface• Profibus Master Plc Ipc• Ethernet / Profibus Dp Gateway• Temperature Transmitter Pt 100 Sensing Element• Differential Pressure Transmitter Measuring Ranges From –10...+10 Mbar To –40...+40 Bar• Venturi Tube And Parts• Three Phase Pump 0.37 Kw, Flow Rate Up To 40 Litres Per Minute, Head Up To 40 Meters• Six Way Profibus Pa Segment ProtectorElectromagnetic Flow Meter• Pressure Transmitter Measuring Ranges Up To 400 Bar• Pressure Regulator With Gauge• Manual Control Valves• Ethernet Switch • Scada Software• Global Control Valve• Plc Configuration And Programming Software• Curriculum Manual And Cd 1.18 Transducer And Instrumentation Trainer:- Input TransducersCarbon Track, Wirewound And Precision Rotary Potentiometers.Slide Potentiometers.Ntc Thermistors.Type ‘K’ Thermocouples.I.C. Temperature Sensor.Photoconductive And Photovoltaic Cell.Phototransistor.Pin Photodiode.Linear Variable Differential Transformer.Linear Variable Capacitor.Strain Gauge.Air Flow And Air Pressure Sensors.Slotted Opto Sensor.Reflective Opto Sensor.Inductive Proximity Sensor.Hall Effect Sensor.Precision Servo Potentiometer.Tachogenerator.Humidity Sensor.Dynamic Microphone.Ultrasonic Receiver.Output DevicesHeater.Filament Lamp.Dc MotorSolenoid Air Valve.Ultrasonic TransmitterBuzzer.Loudspeaker.Relay.Solenoid.Counter / Timer Unit With Led Display.Bar Graph Voltage Indicator.Analog 10V Center-Zero Meter.Signal ConditioningBuffers.Inverters.Comparator With Switchable Hysteresis.Amplifiers With Gain And Offset Control.Current Amplifier.Summing AmplifierDifferential Amplifier.Instrumentation Amplifiers.Ac And Power Amplifiers.Oscillator 40Khz.Filter 40Khz.Low-Pass Filter With Switchable Time Constant.Precision Full-Wave Rectifier.Sample And Hold Circuit.Integrator With Switchable Time Constant.Differentiator With Switchable Time Constant.Converters: V / F, F / V, V / I, I / V.Alarm Oscillator With Switchable4Mm Patch CordsManual 1.19 Pressure Measurement Trainer:- Pressure Cell : 10Kg / Cm²Pressure Source : Foot Pump To Build Pressure Upto 5Kg / Cm²Indicator : 3½ Digit Display To Read Upto 10 Kg / Cm²Resolution : 0.1 Kg / Cm²Led Indicators; Facility For Interface, With MicrocontrollersOn Board Programming Faciliy 1.2 Pressure Measurement Using Bourdon Tube:- Pressure Source: Foot Operated Air Pressure Pump To BuildPressure Max. 7Kg / Cm2Dial Gauge: Bourdon Tube Pressure Gauge Of 10 Kg / Cm2Pressure Transducer: Diaphragm Type Strain Gauge Based SensorRange 10 Kg / Cm2Strain Gauges: 350 Ohms Resistance, Gauge Factor 2 - 2.1Display: 31 / 2 Digit 7 Segment Led DisplayExcitation Voltage: 10 VAccuracy: 1%Resolution: 0.01 Kg / Cm2Power Supply: 230 V + / - 10% 50 Hz 1.21 Capacitance Trainer:- Plate CapacitanceSensor Material: Aluminum PlatesDielectric Medium: AirDisplacement: 0 To 50Mm / 0-900Accuracy: 5 To 10%Display: 3.5 Digit Led Display To Read + / - 1999 Counts For + / - 20Mv FsdPower: 230V + / - 10% 50 Hz 1.22 Strain Measurement Trainer:- • Transducer: Temperature Compensated Strain Gauges• Type: Cu-Ni Foil With Polyamide Carrier Base• Gauge Resistance: 350 Ohms ( Nominal ) • Gauge Length: 6 Mm, • Gauge Width: 2.4 Mm• Gauge Base: 12.5 Mm X 4.3 Mm, • Gauge Factor: 2:1 ( Approx ) • Transducer: Strain Gauges Mounted On A Stainless Steel Cantilever Beam• Configuration: Bridge With Two Arms As Strain Gauges• Wheatstone Bridge Principle• Range: 0 – 500 Grams• Excitation Source: Dc Regulated Source• Readout: Digital Display To Indicate Strain In Kilograms• Test Points: Multicoloured Test Points Provided• Indicator: Mains On / Of• Power Requirements: 230V, 10% Ac, 50 Hz, 1Phase 1.23 Displacement Measurement Trainer:- Transducer: Linear Variable Differential Transformer ( Lvdt ) For Linear Displacement • Type: Spring Loaded Core Type • Configuration: Axial Type Lvdt Full Stroke: + 10 Mm Range • Actual Displacement: By Micrometer Arrangement Pitch: 1 Mm • Circuit: Ac Excitation Source, Phase Detector & Digital Display • Excitation Source: Sine Wave Of 2 Khz To 5 Khz Variable Frequency And 0 To 5V Variable Amplitude • Readout: Digital Display To Measure 0 To + / - 10 Mm, Indicating Displacement In Millimeters With Core In / Out Indicated By + Sign • Test Points: Multicoloured Test Points Are Provided At Various Stages To Observe The Waveforms And Voltages • Instruction Manual• Operating Voltage: 230V, + 10 % Ac 1Phase 1.24 Vibration Measurement Trainer:- Vibration SourceVibration Generator Capacity 5 New Tons.Power Amplifier0 To 10V P To P Variable By Potentiometer.50 To 1000Hz Variable By PotentiometerVibration SensorAccelrometer [ Piezo Electric Crystal ) Indicator4½ Digit 16 X 2 Line Lcd DisplayParameter DisplayedAccelration, Velocity, Displacement And Frequency.Power Supply230V ± 10% @ 50 Hz 1.25 Pressure Control Station:- Pressure Tank Fitted With Pressure Transmitter To Measure The Pressure. Pneumatic Control Valve Operated By A I To P Converter. Air Compressor. Adc / Dac Card With Rs-232 Interface. Displays Indicate The Process Value And Set Value In The Pc Through Rs - 232 C PortSoftware For Experimentation, Pid Control Sesttings ( P, Pi, Pd And Pid Mode ) Data Storing, Online Data Acquisition, Off Line Analysis, Printing Of Data. 1.26 Dc Position Servo System Trainer:- Displacement: Angular ( 00 To 2700 ) • Input Transducer: Command Or Master Potentiometer With Calibrated Dial ( 00 To 2700 ) • Motor: Specially Designed Bi-Directional, Geared, Permanent Magnet Armature Controlled Dc Motor• Instrumentation: Amplifiers Pre-Amplifier ( Differential Amplifier ) , Summing Amplifier Of Adjustable Gain & Span ( Error Amplifier ) And Power Amplifier For Driving Dc Motor On Basis Of Error Signal • Output: Slave Dial Coupled To The Servo Mechanism And Mounted With Calibrated Dial ( 00 To 2700 ) .• Controls: Master Or Command Control ( Input Potentiometer ) , Zero Adjust Control For Minimum ( Lower Limit ) Of Angular Displacement, Span Adjust Control For Maximum ( Upper Limit ) Of Angular Displacement, Gain Adjust Control, Dc Servo Motor On / Off Control And Mains On / Off • Indicators: Digital Deviation ( Error ) Meter In Degrees, Dc Servo Motor On / Off And Mains On / Off • Test Points At Various Stages In To Observe The Waveforms And Voltages• Power Requirements: 230V, ± 10% Ac, 50 Hz, 1 Phase 1.27 Force Measurement Trainer:- Transducer : Load Cell• Type : Strain Gauge Type• Configuration : Full Active Bridge• Circuit : Bridge Configuration, Dc Excitations Source And Electronic• Excitation Source : In-Built Dc Voltage• Readout : Digital Display To Measure Force In Kilograms ( Kg ) • Test Points At Various Stages In To Observe The Waveforms And Voltages• Operating Voltage : 230V + 10 %, 50 Hz, Ac Mains, 1 Phase 1.28 Measurement And Control Of Temperature Trainer:- Control System : On / Off Type• Transducer : Thermocouple• Type : Fe-K ( Iron-Constantan ) • Sensor Range : 0 To 4000 C• System Range : Variable From Ambient ( Room ) Temperature’S To 700 C• Actual Heating Process : Aluminium Block With Heater• Set Point : Adjustable• Readout : 3.5 Digit Digital Display, Dual Mode To Read Set Temperature In 0C And Actual Temperature In 0C• Controls : Set Point Control, Display Mode Control And Mains On / Off Control• Power Requirements : 230V, 10% Ac, 50 Hz, 1 Phase 1.29 Basic Feedback Control System:- • Demonstrates The Principle & Working Of Basic Feedback Control System• Provision To Vary The Input Command & Disturbance• Switches Provided To Start The Process & Provision To Discharge• Supply Required 230V, 50 Hz Ac 1.3 Dc Servo Motor Demonstrator:- • Demonstrates The Principle & Working Of A Dc Servomotor• Determine The Speed Torque Characteristics Of An Dc Servomotor• Specially Designed Dc Servo-Motor With Required Power Supply Of 12 V Dc• A Rope Brake Pulley Loading Arrangement Is Provided For Loading Of The Dc Servomotor• The Arrangement Consists Of A Pulley Connected To The Shaft Of The Dc Servomotor, Spring Balance And The Rope Coupled Across The Pulley• A Non-Contact Type Tachometer Arrangement Using An Opto Coupler Is Provided Along With A Microcontroller Based Digital Rpm Meter For Accurate Rpm Measurement Of The Dc Servomotor• Plotting The Characteristics Of Speed V / S Torque For The Dc Servo Motor• Multicoloured Test Points Are Provided At Various Stages To Observe The Voltages And Waveforms• The Dc Servo Motor With Loading Arrangement Module / Unit Along With Necessary Wires / Connector Is Separately Provided• 230 V Ac, 50 Hz, 1 Phase Mains Operated 1.31 Basic Electronic Trainer:- • Ohms Law, Rc - High Pass And Low Pass Circuits, Rl - High Pass And Low Pass Circuits, Rlc Series And Parallel Resonance Circuits, Kirchoffs Current And Voltage Laws• Transformer’S Turns Ratio, Efficiency Of A Transformer, Relay As A Switch• Diode Characteristics, Clipping And Clamping Circuits, Half - Wave And Full - Wave Rectifiers, Zener Diode Characteristics & As Regulator, Regulators ( Line And Load ) , Diode Logic Gates Transistor ( S ) Characteristics Of Cb, Ce & Cc Configurations• Transistor ( S ) Amplifiers ( Cb, Ce & Cc ) , Power Amplifiers, Differential Amplifiers, Feedback Amplifier Current Series And Current Shunt, Rc Phase• Shift Oscillator, Bistable, Monostable And Astable Multivibrators, Schmitt Trigger, Transistor Logic Gates• Fet Characteristics, Fet As A Source Follower, Fet As A Voltage Variable Resistor• Mosfet Characteristics & Its Application• Ujt Characteristics, Ujt As A Relaxation Oscillator• Triac / Diac Characteristics, Power Control Using Diac And Triac.• Scr Characteristics, Phase Control Using Scr• Ldr Characteristics & Its Application 1.32 Power Measurement By Two Wattmeter Trainer:- Input Supply : Three Phase Mains 415 V ±10 % Ac, 50 Hz • Load : Resistive ( R ) And Inductive ( L ) • Meters : Wattmeters - 500 W - 2 Nos., Voltmeter ( Mi ) - 500 V - 1 Nos. And Ammeter ( Mi ) - 1 A - 1 Nos. • On / Off : Mcb • Indicators : R, Y, B 1.33 Function Generator With Frequency Counter:- • Frequency - 0.1-2Mhz• Output Waveforms - Sine, Triangle, Square, Positive And Negative Pulse Positive And Negative Sawtooth• Output Impedance - 50Ω 10 ± %Amplitude - Not Less Than 20Vp-P ( Open Circuit ) • Dc Voltage - Upto ± 10V Continuously Adjustable• Symmetry Range - 90:10 -- 10:90• Rising Edge Of Square - : Less Than 100Ns. 1.34 Ni Elvis Ii Trainer:- Latest Configuration 1.35 Split Range Control Trainer:- Sump Tank: Capacity: 30 Liters, Centrifugal Pump : - 1 H.P., 230 Vac 50 HzLevel Transmitter ( With Level Loop ) : - Input: 0-400 / 0-500 Mm, Output: 4-20 Ma, Supply: 24 V Dc, 100 Ma, Type: 2-Wire Capacitance Type Pressure Transmitter ( With Pressure Loop ) Type: 2-Wire Piezoresistive Type Pneumatic Control Valve: - 2 No. Rotameter: - 1 No. Electronic Pid Controller: - 1 No., Single Input Pid With Serial Interface ( Ascii Protocol ) Scada Application Software ( Optional ) : - Scada S / W, And Pid Mode, Auto / Manual Tuning Of Pid, Data Storage, Off Line Analysis, Online Data Acquisition, Simulation And Printing Of Data In Graphical And TabularForm. Interactive Graphical User Interface ( Gui ) Includes. Air Compressor ( Optional ) : - Tank Capacity: 30 Liters, Motor: ½ H.P. 230 V Ac Operated, Working Pressure: 3-4 Kg / Cm2 1.36 Cascade And Ratio Control Trainer:- Sump Tank- Capacity: 30 LitersLevel Tank-Centrifugal Pump-. H.P., 1Φ 230 V Ac SupplyFlow Meter-2 Nos. , Turbine Type / Wfm Type, Range: 0-600 Lph / 0-1000 Lph. Output: 4-20 Ma, Type: 3-Wire Type, Supply: 24 V Dc: 100 MaLevel Transmitter-Input: 0-400 / 0-500 Mm, Output: 4-20 Ma, Supply: 24 Vdc, 100 Ma.Type: 2-Wire Capacitance TypeLevel Switch-Float Operated, Switch Action: ReversiblePneumatic Control Valve-Size: 1 / 2.’’, Type: Two Way Globe Type ( Air To Close ) , Equal Percentage Type, With Diaphragm Actuator.Rotameter-2 N O. Range: 0-1000 LphE / P Converter-Input: 4-20 Ma, Output: 3-15 Psi Electronic Pid Controller-2 No. Single Input Pid ( 1 N0. ) & Dual Input ( 1 No. ) , For Cascade And Ratio, With Serial Pc Interface ( Ascii Protocol ) Usb / Ethernet / Rs 485 / Rs 232Scada Application Software ( Optional ) - Scada S / W, Pid Control Setting ( P, Pi, Pd And Pid Mode ) , Auto / Manual Tuning Of Pid, Data Storage, Off Line Analysis, Online Data Acquisition, Simulation And Printing Of Datain Graphical And Tabular Form.Air Compressor ( Optional ) - Tank Capacity: 25 Liters, Discharge: 2 Cfm, Motor: 2 H.P. 230 V Ac Operated, Working Pressure: 5-6 Kg / Cm2. 1.37 Cascade Control Trainer:-Cascade Control Trainer:- Sump Tank- Capacity: 30 Litres Level TankCentrifugal Pump- . H.P., 1Φ 230 V Ac SupplyFlow Meter- Turbine Type / Wfm Type, Range: 0-600 Lph / 0-1000 Lph. Output: 4-20 Ma, Type: 3-Wire Type, Supply: 24 V Dc, 100 MaLevel Transmitter- Input: 0-400 / 0-500 Mm, Output: 4-20 Ma, Supply: 24 V Dc: 100 Ma, Type: 2-Wire Capacitance TypeLevel Switch- Float Operated, Switching Voltage: 240 Vac 200 Vdc, Switch Action: ReversiblePneumatic Control Valve- Type: Two Way Globe Type ( Air To Close ) , Cv: 5 Us Gpm With Diaphragm Actuator, Equal Percentage TypeRotameter- 1 No. Range: 0-10S00 LphE / P Converter- Input: 4-20 Ma, Output: 3-15 Psi Electronic Pid Controller- 2 No. Single Input Pid ( 1 N0. ) & Dual Input ( 1 No. ) , With Serial Pc Interface ( Ascii Protocol ) Usb / Ethernet / Rs 485 / Rs 232, Input: 4-20 Ma, Output: 4-20 Ma, Display: Dual For Pv & Sp, Bar Graph Display For Output & Deviation. Hi-Low Alarm Annunciation.Scada Application Software ( Optional ) - Scada S / W, Pid Control Setting ( P, Pi, Pd And Pid Mode ) , Auto / Manual Tuning Of Pid, Data Storage, Off Line Analysis, Online Data Acquisition, Simulation And Printing Of Datain Graphical And Tabular Form.Air Compressor ( Optional ) - Tank Capacity: 25 Litres, Discharge: 2 Cfm Motor: 2 H.P. 230 V Ac Operated, Working Pressure: 5-6 Kg / Cm2 )
