Quotation Are Invited For I/P Transducer 500Ac

Quotation are invited for I/P Transducer 500ac Delivery Date: 2025/06/30 Delivery To: Blackheath WTP Blackheath WTP Delivery Address: 0000 Blackheath WTP, CAPE TOWN Closing Date: 2025/05/02 Closing Time: 12:00 PM Description: 10 each x i/p transducer 500ac Specification: * `QUOTATION CONDITIONS NB PLEASE SUBMIT SAMPLE PICURE OR SPESIFICATION SHEET, IF NOT RECEIVED YOU MAY BE DEEMED NON COMPLIANT ********************************************** CLAUSE - 2.14.1 & 2.15 Provide, on request by the CCT, any other material that has a bearing on the quotation offer, the supplier#s commercial position (including joint venture agreements), preferencing arrangements, or samples of materials, considered necessary by the CCT for the purpose of the evaluation of the quotation. If the Specifications require the supplier to provide samples/technical data sheets, these shall be provided strictly in accordance with the instructions set out in the Specification. If such samples /technical data sheets are not submitted as required in the bid documents or within any further time stipulated by the CCT in writing, then the bid concerned may be declared non-responsive. ************************************* # Wherever reference is made to any particular Trade Mark, Name, Patent, Design, Type, Specific Origin or Producer, such reference shall be deemed to be accompanied by the words or equivalent # NB: The Municipal Bidding Document 6.1 (MBD 6.1) is attached, in order to be eligible for preference points bidders are required to submit a duly completed, current dated MBD 6.1 document with supporting documents with each and every RFQ submission, failure to submit will result in zero point allocation. ************************************************ *** PLEASE ENSURE THAT ALL REQUIRED INSURANCES SUCH AS YOUR PUBLIC LIABILITY, EMPLOYERS LIABILITY OR COIDA AND MOTOR VEHICLE INSURANCE ARE ATTACHED AND THAT THEY ARE UP-TO-DATE. IF YOU UTILISE COURIERS AND DO NOT HAVE MOTOR VEHICLE INSURANCE, THEN PLEASE MENTION THIS. ALSO ENSURE THAT YOUR UPDATED DECLARATION OF INTEREST AND BBBEE IS ATTACHED AT ALL TIMES*** Electropneumatic Transducer I/P Type 500X - Model 500AC Input: 4-20 mA Output: 3-15 psig Supply: 18-100 psig Min./Max. Supply Pressure: Minimum - 3psig (2.1Bar) above maximum output. Maximum - 100psig (7 Bar) Supply Pressure Sensitivity: +/- 0.1% of span per psig ( +/- 0.15% of span per 0.1 Bar) Terminal Based Linearity: +/- 0.75% of span Repeatability: 0.5% of span Hysterisis: 1.0% of span Response Time: Dependent on pressure range - typically less than 0.25sec for 3-15 psig units Flow Rate: 4.5 scfm (127NI/min) at 25 psig 1.7 Bar supply 12.0 scfm (340NI/min) at 100psig (6.8 BAR) supply Maximum Air Consumption: .05scfm (1.4 NI/min) midrange typical Media: Oil Free, clean dry air filtered to 40 micron Electrical Connections: Conduit 1.2 NPT (standard); DIN 43650 (optional) Enclosure: Nema 1 (standard); Temp Range: -30 degrees Celcius to 60 degrees Celcius Port Sizes: 1/4 NPT (Pneumatic) Relief Capacity: 2 scfm (56.6 NI/min) at 5psig (2.4 BAR) above 20psig (1.3 BAR) setpoint Weight: 2.1 lbs. (0.94kg) Type 500X converts a current or voltage input signal to a linearly proportional pneumatic output pressure. The Type 500X is a force balance device in which a coil is suspended in the field of a magnet by a flexure. The flexure moves towards the nozzle and creates back pressure which acts as a pilot pressure to an integral booster relay. Unit may be pipe, panel or bracket mounted. The 1/4 NPT supply & output ports are marked IN and OUT on the base of the unit. Pictures attached Tender Link : http://web1.capetown.gov.za/web1/ProcurementPortal/RFQ/Details/303998

Refer document

FileName	File Description
Global Tender Document	Tender Notice